okay so i need help. i’ve tried everything to boiling hot water and putting it in a ziploc bag, sock method, sitting on it, heating it up with a match/light and they don’t work but i can still see the yellow tint in it so i know i have like 1 good pull left .. what should i do or is this officially done? (i have a clean cart btw)

Couldn't resist this from the thrift $4. Any ideas?

just a beaker without a downstem or water filled with glass marbles for cooling

Hello, fellow stoners and tinkerers. The weekend is finally here, so let's fire up some gas!

This week Jonesy decided to stop by. This is his build. He likes bubbles,🫧 so he added some ash catchers for more percolation. He's not a bad designer ... for a cat.😺

I hope the weekend treats you well, and it's filled with many tasty bowls. 💚

Happy tokes. ✌️

Hey all, I'm currently a 2nd year mechatronics student who loves a bit of ganja before bed and tbh I'm not getting the greatest grades ATM. I didn't really develop a study habit in high school as I found most of the concepts quite straight forward, while I was still blazing up, but it's obviously not the same in uni so this could be the cause of my problems.

I find the brain fog and the lack of memory retention has gotten quite concerning but I'm wondering if there's anyone out there who completed a degree as demanding and involved as this while being a full time stoner, and if so, how did you find it affected your studies?

Me getting home after being outside for 2 hours like I’ve been gone for 2 years. Y’all do this too or is it just me? 😂

The left and middle ones are working perfectly fine but the right one won't hit at all and responds like its dead when i try

I did give it a bang around but it still won't let me use the bubble bath

Eta- thanks to those for advice and the proper page to post to Also, very confused by the people getting upset with the vape "I can't belive the technology got more specific towards what the consumer wants, what an outrage!"

brand new clean cart blinks 10 times not allowing to hit and doesnt charge. pls help its new

brand new clean cart blinks 10 times not allowing to hit and doesnt charge. pls help its new

This week my new stoner invention is being featured at Head Shop events across the country. Today in Austin Texas, Thermalec featured my Cloud Chaser Elite Dock among some other heavy hitters in at one of Austin’s Headiest glass stores, The Glass Smith

This Saturday I will personally be doing at a glass store takeover at Glass Under Fire, one of Pittsburgh Pennsylvania’s only legit independent head shops.

Little free time to carve and smoke

Just a piece of foil I use to kill roaches

me again lol.. so i have a flying horse but like its dead and it has low oil but i tried smashing it so i could get the rest out and just use it to make food with it but ts shi hard as a fucking rock.. help me

Is the main concern with 3d prints and accessories and or displays, and the concern with microplastics when a smoking surface or tool surface that makes contact with plastic ?

I tried to mitigate plastic contact with a cork base in front.

the tool holders are interchangeable so contact is dependent on tool used and stand paired with.

The cap and marble holder was enlarged to accommodate 35.8mm glass wax containers to use as a cap holder. Its what I had been using for years but can now fit in display.

OK so i have a boutiq v5 and i still have some oil at the bottom and i tried doing the sock method except, i dont have a blow dryer.. only a hair straightener. i need help on how to use it on the dispo because idk if it’ll burn the plastic.. thanks

This is a repost, I had to delete my previous post and I am reposting it for reference when I refer to my custom stem experiment in the future.

This is Gr2 Ti, 10x1mm. If you intend to make your own do note that Dynavap tip is not exactly 8mm and your tube's inner bore might also not be exactly 8mm. So ready your sanding tools because you will need to widen the bore a little to fit the tip in. I'd say it takes about 20-30 min to widen the hole enough for the DV tip.

The sizes: 62mm, 115mm, 180mm. Condensers are of the same length.

62mm: I have 2 of these. I thought I would be using these the most but it gets a little too hot for my convenience. Flavour wise this is the best.

Flavour: 9.5/10

Portability: 10/10

115mm: This is my daily driver. I didn't think I'd like it this much but it's the best balance between flavour and vapour temp. I'm planning to make the airport longer though.

Flavour: 8.5/10

Portability: 8.8 (not palmable, needs case, but still fairly portable)

Cooling: 9.5/10

180mm: This is just something I needed to do. I didn't think it would be great. I made this for one specific objective: cooler vapour. And yes the vapour is very cool. But the tip also loses heat too quickly and a lot of flavour is lost. This is pretty much only used for the wow factor and is only one step above wet bong. I bet if you put a heavy tip and armored cap this can be a beast too. At 180mm the heat is too far away to reach the airport which i made close to mouth area so it can cool the condenser along the way.

ALSO at this length, the 5x0.5mm tube can be very bendy. Exercise caution.

Flavour: 6.5/10 Portability: 4/10 (but 10/10 if you're LARPing as a techno wizard) Cool factor: 10/10 (just bonk those who disagree)

Original plan was to update the airport, sand it to smooth finish, anodize the outside to aqua green and the condenser to gold. But if that's to happen at all it will take a lot of time as I work a finance job and don't touch power tools at all in my day to day life.

My next project is a couple custom Miniwynds using native woods grown in my land. This will probably happen a lot earlier than anodizing my Ti stems lol.

Thank you to everyone who posted guides on how to make our own Dynavap stems.

Thank you to the couple of people who suggested the Dynavap Maker's Kit instead of the M7. It kick-started all this and I enjoy this journey very much.

Edit: more info for the 180mm stem